[Q14-Q36] 最高のNSE5_FAZ-6.4のPDF問題集100%GoShiken試験合格率保証 [2022年07月]

Rate this post

最高のNSE5_FAZ-6.4のPDF問題集100%GoShiken試験合格率保証 [2022年07月]

GoShikenの問題集で100%あなたのNSE5_FAZ-6.4 Fortinet NSE 5 – FortiAnalyzer 6.4試験を一発合格

質問14、 What can the CLI command # diagnose test application oftpd 3 help you to determine?

What devices and IP addresses are connecting to FortiAnalyzer

What logs, if any, are reaching FortiAnalyzer

What ADOMs are enabled and configured

What devices are registered and unregistered

質問15、 Refer to the exhibit.

What does the data point at 14:55 tell you?

The received rate is almost at its maximum for this device

The sqlplugind daemon is behind in log indexing by two logs

Logs are being dropped

Raw logs are reaching FortiAnalyzer faster than they can be indexed

質問16、 What two things should an administrator do to view Compromised Hosts on FortiAnalyzer? (Choose two.)

Enable web filtering in firewall policies on FortiGate devices, and make sure these logs are sent to FortiAnalyzer.

Enable device detection on an interface on the FortiGate devices that are connected to the FortiAnalyzer.

Subscribe FortiAnalyzer to FortiGuard to keep its local threat database up-to-date.

Make sure all endpoints are reachable by FortiAnalyzer.

質問17、 Which two statements are true regarding FortiAnalyzer log forwarding? (Choose two.)

In aggregation mode, you can forward logs to syslog and CEF servers as well.

Forwarding mode forwards logs in real time only to other FortiAnalyzer devices.

Aggregation mode stores logs and content files and uploads them to another FortiAnalyzer device at a scheduled time.

Both modes, forwarding and aggregation, support encryption of logs between devices.

質問18、 Logs are being deleted from one of your ADOMs earlier that the configured setting for archiving in your data policy. What is the most likely problem?

The total disk space is insufficient and you need to add other disk.

CPU resources are too high.

The ADOM disk quota is set too low based on log rates.

Logs in that ADOM are being forwarded in real-time to another FortiAnalyzer device.

質問19、 Which statements are true of Administrative Domains (ADOMs) in FortiAnalyzer? (Choose two.)

ADOMs are enabled by default.

ADOMs constrain other administrator’s access privileges to a subset of devices in the device list.

Once enabled, the Device Manager, FortiView, Event Management, and Reports tab display per ADOM.

All administrators can create ADOMs–not just the admin administrator.

質問20、 On FortiAnalyzer, what is a wildcard administrator account?

An account that permits access to members of an LDAP group

An account that allows guest access with read-only privileges

An account that requires two-factor authentication

An account that validates against any user account on a FortiAuthenticator

質問21、 What is the purpose of a predefined template on the FortiAnalyzer?

It can be edited and modified as required

It specifies the report layout which contains predefined texts, charts, and macros

It specifies report settings which contains time period, device selection, and schedule

It contains predefined data to generate mock reports

質問22、 In FortiAnalyzer’s FormView, source and destination IP addresses from FortiGate devices are not resolving to a hostname. How can you resolve the source and destination IPs, without introducing any additional performance impact to FortiAnalyzer?

Configure local DNS servers on FortiAnalyzer

Resolve IPs on FortiGate

Configure # set resolve-ip enable in the system FortiView settings

Resolve IPs on a per-ADOM basis to reduce delay on FortiView while IPs resolve

質問23、 Which statements are true regarding securing communications between FortiAnalyzer and FortiGate with IPsec? (Choose two.)

Must configure the FortiAnalyzer end of the tunnel only–the FortiGate end is auto-negotiated.

Must establish an IPsec tunnel ID and pre-shared key.

IPsec cannot be enabled if SSL is enabled as well.

IPsec is only enabled through the CLI on FortiAnalyzer.

質問24、 What are analytics logs on FortiAnalyzer?

Log type Traffic logs.

Logs that roll over when the log file reaches a specific size.

Logs that are indexed and stored in the SQL.

Raw logs that are compressed and saved to a log file.

質問25、 Which daemon is responsible for enforcing raw log file size?

logfiled

oftpd

sqlplugind

miglogd

質問26、 What remote authentication servers can you configure to validate your FortiAnalyzer administrator logons? (Choose three)

RADIUS

Local

LDAP

PKI

TACACS+

質問27、 What is the purpose of employing RAID with FortiAnalyzer?

To introduce redundancy to your log data

To provide data separation between ADOMs

To separate analytical and archive data

To back up your logs

質問28、 If you upgrade your FortiAnalyzer firmware, what report elements can be affected?

Output profiles

Report settings

Report scheduling

Custom datasets

質問29、 What is Log Insert Lag Time on FortiAnalyzer?

The number of times in the logs where end users experienced slowness while accessing resources.

The amount of lag time that occurs when the administrator is rebuilding the ADOM database.

The amount of time that passes between the time a log was received and when it was indexed on FortiAnalyzer.

The amount of time FortiAnalyzer takes to receive logs from a registered device

質問30、 What happens when a log file saved on FortiAnalyzer disks reaches the size specified in the device log settings?

The log file is stored as a raw log and is available for analytic support.

The log file rolls over and is archived.

The log file is purged from the database.

The log file is overwritten.

質問31、 If you upgrade the FortiAnalyzer firmware, which report element can be affected?

Custom datasets

Report scheduling

Report settings

Output profiles

質問32、 Which two statements are true regarding fabric connectors? (Choose two.)

Configuring fabric connectors to send notification to ITSM platform upon incident creation Is more efficient than third-party information from the FortiAnalyzer API.

Fabric connectors allow to save storage costs and improve redundancy.

Storage connector service does not require a separate license to send logs to cloud platform.

Cloud-Out connections allow you to send real-time logs to pubic cloud accounts like Amazon S3, Azure Blob , and Google Cloud.

質問33、 What are two of the key features of FortiAnalyzer? (Choose two.)

Centralized log repository

Cloud-based management

Reports

Virtual domains (VDOMs)

質問34、 View the exhibit.

What does the data point at 14:35 tell you?

FortiAnalyzer is dropping logs.

FortiAnalyzer is indexing logs faster than logs are being received.

FortiAnalyzer has temporarily stopped receiving logs so older logs’ can be indexed.

The sqlplugind daemon is ahead in indexing by one log.

質問35、 Which two statements are true regarding high availability (HA) on FortiAnalyzer? (Choose two.)

FortiAnalyzer HA can function without VRRP. and VRRP is required only if you have more than two FortiAnalyzer devices in a cluster.

FortiAnalyzer HA supports synchronization of logs as well as some system and configuration settings.

All devices in a FortiAnalyzer HA cluster must run in the same operation mode: analyzer or collector.

FortiAnalyzer HA implementation is supported by many public cloud infrastructures such as AWS, Microsoft Azure, and Google Cloud.

質問36、 Which statement is true regarding Macros on FortiAnalyzer?

Macros are ADOM specific and each ADOM will have unique macros relevant to that ADOM.

Macros are supported only on the FortiGate ADOM.

Macros are useful in generating excel log files automatically based on the reports settings.

Macros are predefined templates for reports and cannot be customized.

トレンドなNSE5_FAZ-6.4のPDF問題集を受験前に使おう：https://www.goshiken.com/Fortinet/NSE5_FAZ-6.4-mondaishu.html

Tags: NSE5_FAZ-6.4トレーニング資料, NSE5_FAZ-6.4受験対策解説集, NSE5_FAZ-6.4専門知識内容, NSE5_FAZ-6.4日本語対策問題集, NSE5_FAZ-6.4関連資格試験対応

[Q14-Q36] 最高のNSE5_FAZ-6.4のPDF問題集100%GoShiken試験合格率保証 [2022年07月]

コメントを残すコメントをキャンセル

関連認証

NSE5_FAZ-6.4 練習テスト

最近の投稿

アーカイブ

カテゴリー

[Q14-Q36] 最高のNSE5_FAZ-6.4のPDF問題集100%GoShiken試験合格率保証 [2022年07月]

コメントを残す コメントをキャンセル

関連認証

NSE5_FAZ-6.4 練習テスト

最近の投稿

アーカイブ

カテゴリー

コメントを残すコメントをキャンセル